Welcome everyone to the third and final part of my recent Chibi-Knight project! This has been such a fun little endeavour, and today you finally get to take a look at the finished model, so here goes:
The paintjob for the actual Knight was actually just about finished last time. So here’s where we left off:
This only really left the basing, but since the objective with this entire model was to match the bigger version as closely as possible, I wanted this ethos to extend to the base as well. So for starters, check out the base of the bigger version of Gilgamesh:
As you can see, I used some pieces from the Space Marine statue from the Honoured Imperium terrain kit to represent fallen Imperial monuments, and I really wanted to recreate that look — and it seemed that fate was very much on my side…
I actually realised a long time ago that the aforementioned statue seems to have been created mostly by upscaling existing Space Marine bitz: If you take a closer look, many of the parts of the statue seem to consist of bigger versions of plastic bitz from the company champion that comes as part of the old Space Marine command squad box (incidentally, I am pretty sure the statue’s cape is an upscaled chaos warrior cape, but that’s beside the point). And I actually discovered a while ago that GW used a face very similar – if not identical – to the statue’s face for different kits as well. So it didn’t take much work to collect the pieces that would allow for a very close recreation of my original design for the base. Take a look:
The shield on the left is pretty much the exact same shield also worn by the Honoured Imperium statue. It came from the aforementioned Space Marine command squad kit. The sword is from a plastic Terminator — I’ll admit the company champion’s sword would have been a better fit from a visual standpoint, but the Terminator sword worked better due to its size and proportions. And the head on the right is a piece of a broken Imperial monument from the WFB/AoS giant.
So I used these parts (or rather, copies of these parts) to create a setup that was fairly similar to the original base:
Now I had to improvise a bit, due to the bigger Knight’s base having an oval shape (and hence more room), but I think the setup worked out pretty well. I also chose to have the head in an upright pose this time around — something I should have done on the bigger base as well.
So here’s the base after undercoating…
…and with the Knight provisionally placed on top:
And here’s the finished base, painted to fit the bigger version:
So all that was left was to affix the new Chibi-Gilgamesh to his new home, and then the model was done. So here, once again, the big version for the sake of comparison:
And without further ado, I give you
Chibi-Gilgamesh version 2.0
I am actually really happy with the way the model has turned out. I may have had to compromise a bit here and there because a couple of visual touches from the bigger model just couldn’t be reproduced at the smaller scale (at least not without ending up looking extremely goofy, that is), but you can still tell at a glance that this is supposed to be Gilgamesh at a smaller scale, wouldn’t you agree?
And there’s also my favourite part about this project, the somewhat harebrained, yet ultimately successful, scheme of adding a fully sculpted interior and pilot to a Knight at the Adeptus Titanicus scale. Check out the bigger version of Baron Harrowthorne again:
And here’s the chibi-version:
And now that the new model has been finished, here’s another comparison shot with its predecessor:
As I’ve said before, I really like how the older Chibi-Knight seems to represent the somewhat clunkier vintage Epic 40k design, while the new model fits the sleeker, more faithful designs from the new Adeptus Titanicus.
That’s not quite all, though. Because with the model finished, it was of course time to trot out the actual 28mm Gilgamesh in order to find out how well the new Chibi-Knight stands up to the big guy.
well,…
I think there’s definitely quite a bit of family resemblance, wouldn’t you agree?
Having managed to closely recreate the base also makes me stupidly happy, to be honest 
So yeah, a fun project all around! And you know what? I am also going to pledge this little guy as part of Azazel’s Mechanical November ’18 community challenge — fits well enough, I’d say
In any case, it goes without saying that I would love to hear any feedback you might have! And, as always, thanks for looking and stay tuned for more! 
